Honda D Series Forum banner
Cancel
Create thread New Garage Forums
Status
Not open for further replies.

D15b VTEC FAQ

Jump to Latest
325K views 640 replies 183 participants last post by  J_PEZ  
#1 · (Edited)
D15b Vtec Faq

Hi guys, I no longer frequent this forum anymore. Most of the info here is very up-to-date as far as I know. I have not been able to read through it all but there are others here knowledgeable who can answer your questions if what I have is not sufficient.:bigok:

Image


I figure I would make the definitive D15B FAQ. It's currently in the works and it will have lots of info. I'm getting tired of seeing the d15b threads over and over.

D15B specs:
Horsepower
130ps @ 6800 rpm (128.22 hp)

Torque
14.1 kg m @ 5200 rpm (101.74 ft lbs)

Fuel Mileage
38 miles/gal (in mode 10 driving? daily driving i guess)
55 miles/gal if you drive 38 mph all day

Transmission with or without LSD
3.250-1
1.900-2
1.250-3
0.909-4
0.750-5
3.153-reverse
4.250-Final

Compression ratio
9.3:1 <-- proof we can use cheap gas

Ferio VTi (sedan) Weight (just to compare)
Base 1040 kg (2293 lbs)
w/ power steering 1060 kg (2337 lbs)
w/power steering and sunroof 1080 kg (2381 lbs)
Click to expand...
SMOG RESULTS WITH P08 MAPS

D15B INSTALL INTO CIVIC

JDM D15B VTEC Honda Parts Numbers!

BRACKETS AND ACCESSORIES WILL SWAP OVER ONTO YOUR NEW BLOCK
 
#2 · (Edited)
As with any engine swap, you'll want to do your major tune-up on the motor while it's out of the car. You have no knowledge of the past history of the motor unless it was from a car that you knew. Just putting the engine without replacing parts is just a time bomb waiting to go off. Save yourself time, swearing, a new motor, and do it right the first time by replacing the parts!

Finding replacement parts for the D15b is a PITA since this motor was not home to the Civics in the US but that of overseas...Japan, Europe, and elsewhere. Don't fret though, your basic maintenance parts can be had here in the US. This FAQ is to help clear the problems involved in searching for parts and make your life easier.

The D15b is essentially a VX block with a EX/Si Head. Majority of the internal parts are unique and cannot be found in the US, but your common maintenance parts are. Parts for the head are for a D16z6 (EX/Si) and the parts for the block are for a D15z1 (VX).

Setting timing: You set the timing on the cam gear as you would on on a D15z1--using the TDC indicators that parallel to the head with the "UP" facing up. You do not use the timing indicator on the 7 o' clock position of the cam gear. Just to be on the safe side when checking timing, use a long rod and stick it inside the number one cylinder to make sure you are actually at TDC.

Waterpump:

The correct waterpump is one for a VX(D15z1)

The waterpump for a D15B7 and a D16z6 are the same. The D15B7 pump shown here is made by the same company as the stocker for the D15b--KeiKen.

Image

top view Left to right: D16z6, D15b7, D15B vtec

Image

inside view left to right: D15B vtec, D15b7, D16z6

Image

corresponding part number and brand. Stock D15B vtec waterpump at the far end.

Image

I bought another water pump but this time at Advance Auto. I didn't like the design on the other water pump since it was nothing near like the stock one. The stock waterpump has, from what I believe, are breather ports for the bearing but I could be wrong. You can notice the opening/passages that lead to the bearing/rotating assembly.

Image

Another angle of the inside view. Stock closest, D15b7, D16z6

Timing Belt:

You need a VX belt. Gates part number is T223.
Image

Image


The Gates T143 (1.5L DX/CX) was too long. The T224(1.6L) was shorter than the T143 but still had some slack. The only way you can run the D16z6 timing belt is if they're using the d16z6 tensioner. Even then, you risk the chance of timing belt teeth catching the lower portion of the engine mount since it's so close to it now.

Spark plugs:
D15B VTEC plugs: ZFR6J-11
Image



Spark plug wires:
Same thing as for a D16z6.

Distributor:
The distributor is the same as the one for the D16z6.

Oil Pan:
D15b7 and D16z6 pan and oil pick ups are the same and will fit the D15B as far as I know. 96-00 D-series pans do not fit from what I've been told.

ECU:
You can run the D15b7 (P06) ecu but you won't have VTEC operation.
You can use a stock D16z6--P28-- ecu without a problem. It would be better to have the ecu chipped and run the P08 maps though.

Don't bother trying to get the stock D15b P08 ECU. Just have your current ECU chipped and run the P08 maps. Plus, you now have the advantage of tuning your car once chipped.

Oxygen sensor:
D15b7, D16z6
You can't use the one wire oxygen sensor that came with the D15b unless you're using the P08 ECU. Also, I don't think you can find the one wire oxygen sensor here in the US.

Fuel injectors:
Same as D15b7, D16z6

Transmission:
Any D-series. Best to get the EX/Si tranny to utilize the power band and the quick acceleration.
 
  • Like
Reactions: guest
Save
Like Like
C
#352 ·
If you read a little further...
Cuong-Nutz said:
Oxygen sensor:
D15b7, D16z6
You can't use the one wire oxygen sensor that came with the D15b unless you're using the P08 ECU. Also, I don't think you can find the one wire oxygen sensor here in the US.
Click to expand...
The d15b o2 sensor is not heated like the ones on north american cars. You need to match the o2 sensor to the ECU. If you have a P28, you need the heated o2 sensor. If you have a P08, you dont. The four wire o2 sensor will work with a P08, as the ECU still gets the signals its looking for.

4bfox said:
Will this O2 sensor work OK? http://cgi.ebay.com/ebaymotors/Hond...em118Q2el1247QQcategoryZ33557QQihZ013QQitemZ230108190815QQrdZ1QQsspagenameZWD1V

How about this P08 ECU?
http://cgi.ebay.com/ebaymotors/Hond...ol-37820-P08-900-JDM_W0QQitemZ320247319427QQcmdZViewItem?hash=item320247319427&

Is the P28 ECU better, or is this one OK?
Click to expand...
P28 is for a d16z6
P08 is for the d15b = right maps for the engine

I cant make any judgements about the ECUs or o2 sensors on ebay... who knows what condition they are in? but if the seller has a high rating, you would probably be ok
 
Save
Like Like
#4 · (Edited)
Timing Belt Tensioner:
The VX and the EX/Si tensioners are the same and are nothing like the one on the D15B VTEC. The D16z6 tensioner is almost the same as the D15B vtec except that it has a slightly larger diameter roller as you will see in the following pictures. I want to say it is safe to use the tensioner for the VX/EX/Si despite the larger roller. All the autoparts store I went to did not have a tensioner for the VX in their database--O'Reilly's, Autozone, and Advance Auto Parts, so stupid me went to the Stealership and ordered one only to find out it's the same as the EX/Si tensioner. The price was twice as much as the ones from the autoparts store, but it came with a new tensioner spring. The tensioner off a D15B7/8 will not work.

Image

Z6/Z1 top, D15B middle, D15b8/d15b7 bottom

Image

Z6/Z1 top, D15b vtec bottom

Image

D15b VTEC tensioner on with VX timing belt. Pay attention to the tensioner spring.

Image

Z6/Z1 tensioner on with VX timing belt. The tensioner spring is stretched further. I'm hoping this will be okay since I'm going to be using it.
 
Save
Like Like
K
#157 · (Edited)
i just assumed knowlege factory and general tech was d-series motors in general...my bad
the original post on this thread talks about d15b7 parts, i assumed the person who created this thread might know the answer to my question, based on this post......
Cuong-Nutz said:
Timing Belt Tensioner:
The VX and the EX/Si tensioners are the same and are nothing like the one on the D15B VTEC. The D16z6 tensioner is almost the same as the D15B vtec except that it has a slightly larger diameter roller as you will see in the following pictures. I want to say it is safe to use the tensioner for the VX/EX/Si despite the larger roller. All the autoparts store I went to did not have a tensioner for the VX in their database--O'Reilly's, Autozone, and Advance Auto Parts, so stupid me went to the Stealership and ordered one only to find out it's the same as the EX/Si tensioner. The price was twice as much as the ones from the autoparts store, but it came with a new tensioner spring. The tensioner off a D15B7/8 will not work.
Click to expand...
 
#5 · (Edited)
Thermostat:
All D-Series thermostats are the same. Designs vary with brands.
Image

stocker and Murray Plus replacement (PN 3187)

Exhaust manifold/Header:
The D15b uses the same 4-2-1 design as the D16z6. The stock exhaust manifold is made out of cast iron. The upper portion of the stock exhaust manifold alone is as heavy as my Megan Racing 4-2-1 header.
Image


Purge solenoid:
The D15B does not come with one, you will have to reuse your old one from your engine. You will have to drill and tap the spot on your D15b intake manifold or stick the purge solenoid on the firewall or somewhere.
Image


Fuel rail accessory:
The D15b came with just a regular hex bolt type fitting to hold the fuel feed hose onto the fuel rail. The US civics have the pulsation damper assembly. Will have to clarify this in the future.
Image

Image
 
Save
Like Like
G
#9 ·
quick question for ya, I need an alternator belt, will any D-series alternator belt fit, I swapped in the D15 Vtec into my CRX HF 91? are there any diffrences? thanks great info.....
 
G
#16 ·
SOHC_Rules said:
i always thought you had to use the timing belt from the block code :hammer: maybe im wrong

wouldnt that be like putting a z6 belt on a stock b7?
Click to expand...

It's my understanding that its the head to belt combo that is correct. On my b7/z6 the b7 belt would have barely fit, but would have been too tight and made noise. The z6 has some slack, but works fine and won't snap from undo tension.

Oh yeah, great info in this thread.
 
G
#17 ·
hey got a new question for ya, do you have like the number for new spark plug wires, some of them are 8.5mm or 9.5 etc whats the diffrence with the D15 or can i just use any from honda (same i mean same year like 92-95 or if it was in a CRX 88-91?) thanks
 
#20 ·
I believe it has to do with emissions. It connects to the charcoal canister and works off the vacuum in the intake manifold. If you disconnect it you will notice an erratic idle. This is on USDM vehicles. Someone can correct me if I'm wrong, which I may possibly be.
 
#22 ·
yea that is exactly what i am getting "erratic idle" and i am throwing a code somewhere so could that possibly be why?

the idle thing is so annoying, i took apart and cleaned the entire intake mannifold looking for a leak or something
 
Save
Like Like
#23 ·
actually, make sure you cap the vac line to the canister, and plug it and see if its still erratic...

My purge solenoid is locked open with my P08.... so there is always vaccum reaching the canister. I unplugged it, and blocked the port and hose end and saw no erratic idle.
 
#24 ·
i have a screw in it now but ill try something a little more durable

what if my ecu was an automatic ecu would this be the problem b/c i am not sure if the guy i bought it from chipped it correctly or not
 
Save
Like Like
#25 ·
well, if its programmed correctly and chipped and modded right the ECU should think its a MT ECU.... that all depends on the guys work =/
 
M
#26 ·
When one swaps a D15B Vtec engine in a car, what should he do before he puts it in.

1. Install new timing belt (is this all that is needed?)
2. What?...

Thanks because when I got mine in, I think I cheated and didnt do anything. My timing belt seems pretty good though the last time I checked. wasnt cracking and seemed pretty hard.

But I think I will just put a new one in the summer. Tell me what should I change...

THANKS
 
Save
Like Like
Status
Not open for further replies.
You have insufficient privileges to reply here.
Honda D Series Forum
posts
2.9M
members
66K
Since
2003
A forum community dedicated to the Honda D Series engine owners and enthusiasts. Come join the discussion about performance, builds, reviews, turbos, and more!
Full Forum Listing
Explore Our Forums
Showcase Forced Induction Engine Building General Tech Engine Management