Honda D Series Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-13 of 13 Results
  1. General Tech
    Ok noob question time and before I get flamed I’ve been researching for a long time and still can’t get a clear answer on this… so I got a d16y8head ,intake, dizzy, harness and ecu for $350 from del sol 97, however once it arrived I realized it’s all obd2, my plan was to do a mini me on my d15b2...
  2. Engine Building
    Ok noob question time and before I get flamed I’ve been researching for a long time and still can’t get a clear answer on this… so I got a d16y8head ,intake, dizzy, harness and ecu for $350 from del sol 97, however once it arrived I realized it’s all obd2, my plan was to do a mini me on my d15b2...
  3. Engine Management
    I am in search of a way to datalog without having to carry a laptop in the car. I came across a bluetooth adapter that plugs onto the 4-pin header on the ECU CN2 Direct ECU Bluetooth Module It appears to be a Moates product based on the picture. Has anyone successfully used this to datalog...
  4. Forced Induction
    I have an 85 civic si, with d16a1 dohc motor, gsp t3t4 57trim turbo, im runing obd0, i have a p28, and a obd1 jumper for it, but i put the p28 in, and it wont even start! Please help
  5. Naturally Aspirated
    My dd is having problems. I was moving it from my driveway to garage after doing and intake IM gasket. when moving the car it the plug wire for cylinder no.1 came off and it ran like this for about 15 seconds. now my car will not start. (its D15b7 with minor mods, z6 IM, header, a6 cam) --The...
  6. General Tech
    So i have a 91 crx dx that did have a d15b2 in it but i pulled blown motor and installed a d16z6 block with intake manifold from a 92-95 ex. i have full engine harness and p28 from the ex. I also have dpfi to obd1 ecu jumper harness and there is a few plugs and two extra wires running on this...
  7. DOHC ZC
    Hi, I'm new to this website and just looking for some answers for my OBD0 to OBD1 conversion I just did. Before I converted the car over to OBD1, the car ran perfect. But now, since I converted it over, I am getting ecu code 9, which is for the crank position sensor. I bought the distributor...
  8. Engine Management
    when reading these directions i found that it doesnt say anything about how to go from dual point to multi point injection are these harness not set up for 4 injectors? http://www.streetlightz.com/Assets/Manual/PreOBD_to_OBD1_manual.pdf
  9. Engine Building
    i got a d15b1 with some eclipse injectors since i put them in is throwing me code 9 the cyp..the distributor i bought it like 6 monthz or a year ago..some people say is the coil of the distributor that is not throwing enought sparks..ok so here is what happends when i take off or in reverse it...
  10. New Member Introductions
    i have a d15b2 and i was going to do a mini me swap but somethings happened and i wasnt able to do it. now i kept the mpfi on there and i have an obd0 to obd1 conversion harness on my d15 but i dont know what distributor to put on because i cant put the stock one because its obd0. i tried a...
  11. New Member Introductions
    I just bought a 89 sedan dx, I want to swap to mpfi. it is a manual. so I have: - Si ECU(PM6 for manual transmission) - Resistor Box(91 Si) w/plug - Si fuel line from filter to fuel rail - Si throttle cable - U shaped coolant hose my questions are.. 1-will a 93 injectors work? I have...
  12. Engine Management
    Hello!! I want to chip two ecus with Real Time Programming See this --> PGMFI.ORG - Grassroots ECU Development - Library . EasyRtpV10 I have 2 ecu's: PM7 88-89 non catalic (out to mod) PM7 90-91 catalyc (in car). My car is catalyc, if i use the PM7 88-89 will work well with O2 sensor...
  13. Engine Management
    Hello! I'm looking for put Wideband o2 sensor (5Wire) on OBD-0 (1 Wire), it can be done?? Or i must put a A/F gauge connected only to new Wideband 02?? I have Chipped OBD-0 with dataloggin interface. Thanks!!
1-13 of 13 Results
Top