Honda D Series Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 19 Results
  1. New Member Introductions
    Hello! I have a daily driver(2003 civic coupe) I like to screw with on occasion, I’ve just had my most grand idea! Taking a 4-2-1 exhaust manifold from a d16 removing its second portion (2-1), then, from the manifold, building two separate pipes that lead to the side of my vehicle, exiting from...
  2. New Member Introductions
    Hey Guys, Bit controversial I know but I'm wanting to fit a UEL manifold to my build, it's more of a sound/appearance build than a performance one. I'm completely stuck with trying to get some headers custom made for the D16 engine instead I can only get them for a B18. I've done some research...
  3. Engine Management
    I noticed on my civic that I have the 3-wire IACV on the bottom of my throttle body, then I have an FITV in my thermostat running from the intake into where the fuel injectors are on the IM. A long time ago the nipples on the FITV broke off, and since then I have blocked where the FITV once was...
  4. New Member Introductions
    Hey guys, I've been a lurker on the forum for a good while now. I've got a 2000 EJ6 sedan and have a few seemingly noobish questions, hear me out. First and foremost: D16 headers. Upon close inspection online, both on forums and vendors, most D16 headers seem to be sorta universal. Is that...
  5. For Sale
    Greetings everyone, Up for sale or trade is a rare piece made by TWM to run either Dual Weber DCOE carbs (or other DCOE design) or itbs with dcoe bolt pattern. It also comes with the linkage as well. This piece has been sitting in storage for years, so its a little scuffed but it is brand new...
  6. New Member Introductions
    I just recently got out of school and I finally have some time to work on my car! Previously, I had made a thread regarding suspension and was met with so much help that I was actually surprised. I mentioned my y7 to y8 intake manifold problems and I was told to make a thread about it so here...
  7. For Sale
    I have for sale a BRAND NEW, unused cast turbo exhaust manifold. I purchased it new for $60 along with the metal gasket for $6. Thanks! Up on ebay now for $10 with no reserve...go get it! lol http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=281058195755
  8. General Tech
    I have a 94 civic ex d16z6 that I just recently built. I am in the break in process now and after driving it today, I popped the hood only to find smoke and oil pooled up betweed the head and the top of the manifold. The exhaust is not gray and thick. the build is as follows: D16Z6 Block 75mm...
  9. General Tech
    hey guys, im currently running a 96 ek2 entirely JDM (ie i live in japan) including the tiny d13b4 motor. i want to do some exhaust and intake work and i need some more info. for the exhaust i havent decided what headers i want to use because im not sure what will all work with minimum...
  10. Engine Building
    95 CX Chassis w/same year engine harness D16Y8 Engine w/ Performer X intake manifold I'm trying to figure out how to hook up the hose from the evaporative emmision purge control diaphragm to the intake manifold. On a D16Z6/D15B8 it looks like this (hose from diaphragm to throttle body): The...
  11. General Tech
    This is pretty simple, but I haven't been able to find a thread that matches my situation. I have a 95 CX chassis (D15B8 ) with a throttle cable that is clearly too short for the Y8 Edelbrock intake manifold. I've got the stock manifold bracket bolted down (like Danz posted in a similar thread)...
  12. Engine Building
    i got a d15 non vtec but i want to improve performance but with other stock d serious engine need help or is it possible. i was thinking like intake manifold or exhaust manifold
  13. Engine Building
    Hello to everyone on d-series i have a d16y5 on my 96 hx and i just discovered that my head is blown so i was wondering if any of you could tell me WHAT EXACTLY DO I NEED TO SWAP IN A D16Z6 HEAD ON MY D16Y5 BLOCK will i need to swap my ecu? if so to what? do i need to swap my engine wiring...
  14. Engine Building
    1996 D16Y8, 4dr. Skunk2 performance intake manifold, Pacesetter header (budget) Very new to the aftermarket scene. I am a mechanic by hobby. Any and all help is appreciated!
  15. Forced Induction
    Groupbuy on Evo 16g manifold? Hey guys, I know I'm new here, but I'm not new to the scene. A few friends and I owned a Honda shop back in the day, and I've owned quite a few Honda's and Evo's. Anyway, getting ready to turbo a D16 in an EG, and was wanting to use some of the bookoo's of evo 8...
  16. For Sale
    whats up all, here is a list of random stuff i have to get rid of. i dont want to get into crazy detail... im tryin to keep it short and simple. ill take best offers but ill put up prices im looking for so no low ballers please. prices shipped. thanks everyone! 52MM AMBER/WHITE A/F GAUGE $30...
  17. General Tech
    i recently bought a skunk2 intake manifold, and i had problems with it. is there anything i have to do with the manifold? do i have to turn my fuel pressure up or get it tuned, or port match with my throttle body? or should it just bolt up without me having to do anything?
  18. Engine Building
    Puttin together a D15B I got, using all parts from a junkyard when I can. First question, is a D16Z6 intake manifold the same as a D15B?
  19. Engine Building
    hey guys, i was wondering if anyone could point out any pictures showing the difference from the manual and auto intake manifold off a d16y8. I would greatly appreciate it.
1-19 of 19 Results
Top