Honda D Series Forum banner
clutch
1-20 of 25 Results
  1. Transmission alley
    Hey everyone i'm new to this forum. I recently did the auto to manual swap and it went fine until i ran into an issue on the first start. There was a loud grinding sound. So i took the trans out and saw this: The pressure plate made contact with that bolt in the bell housing. no mjor damage...
  2. General Tech
    I got a brand new clutch but it's for a 2001 d17 wondering if it still work for a d16 it's a little bigger but I've seen d17 with d16 trans with my clutch and presser plate work for my d16
  3. Transmission alley
    What’s the difference between Sprung and Unsprung? What’s the difference between a 3-4-6 Puck? What’s the best material for a clutch disc? Is it possible to get 500 to 550 out of a steel disc clutch with a heavy duty pressure plate?
  4. Engine Building
    So I'm considering buying this Ebay clutch kit for my Ek hatch (Im not here to discuss if ebay is good or not, just want to see if it will work) So it says it fits 92-05 civcs which is kinda weird since thats 3 different generations. It says it ins't compatible with my CX hatch but the closest...
  5. General Tech
    Hello, I need help diagnosing my clutch issue. My car is a Turbo d16y8 A few nights ago, i was driving home and my clutch was hesitant once or twice in a 50 mile drive to disengage. Parked the car overnight and the next day got into it and the clutch was heavier to engage and disengaged very...
  6. DOHC ZC
    I just recently purchased a 97' Honda Civic Ex with a D16A DOHC ZC, The car needs a new clutch but I can't seem to identify the amount of splines it has, and I do not want to have to remove the gearbox just to identify the clutch, I want to change the clutch the same day I remove the box to save...
  7. Transmission alley
    Hi guys, new member here. I have a 1996 honda civic dx with the stock d16y7 in it. I recently replaced the clutch, throwout bearing, pilot bearing, and slave cylinder after my pedal lost pressure and would not shift into gear. I have a problem shifting after about a half hour of driving. Also...
  8. Transmission alley
    After the suspension and engine are back in my eg, I'm planning on savin up some monies and figuring out which clutch I want. Currently I've got a SPEC 4puck solid hub carbon graphite disc, with a "stage 4" pressure plate. I LLOOOVVVEEEE the engagement and short pedal feel. The only problem...
  9. For Sale
    NEW - Competition Clutch Stage 5 KIT for D16 trannys - SOLD! I am selling my BRAND NEW, NEVER INSTALLED or even unboxed, Competition Clutch Stage 5 (model 8022-1420). It is rated to hold over 300% more torque over the factory clutch which translates to around 300 ft lbs! This is a sprung clutch...
  10. Transmission alley
    So my clutch effed up on me, decided to upgrade, stage 2 exeddy clutch and pressure. Fidanza light flywheel.. slapped everything back together. Somehow, it sounds like my input shaft bearing is bad too. Anyhow, I had to take the tranny back off to check internals, when I was doing so, oil from...
  11. Want to Buy
    Hey Guys, Looking to buy following parts urgently. Let me know what you got. ARP for D16Y8, new ones. ARP D series rod bolts for JDM D15B, new ones. Stage 2/3 Clutch Competition/Act/Exedy with Fidanza flywheel for JDM D15B - Already bought Comp clutch Stage 3 and Fidanza 7LB Flywheel. Looking...
  12. Transmission alley
    Got a D16z6 with fully upgraded fuel system and a .60 trim turbo. Pushing around 225 horses. Just got the car, and the clutch is already all but shot. I want to replace it with something I can put the beans to, and it'll take it like a champ. Any recommendations? Anything else I should do while...
  13. Transmission alley
    Hello everyone!!, I have a 97 EX D16Y8, and I'm planning to turbocharge this engine!!, so I changed my clutch and flywheel, for a Stage 3 XTD clutch with a 8lbs flywheel (Yeah I know what I'm doing with XTD, but I have like 4 friends that are doing good with their hondas). I already had a...
  14. For Sale
    Mazworx has offered to make D-series scatter sheilds, not the blankets. Here is what they will look like (this is a SR20 sheild that Mazworx makes,but will look similar): (These are b-series scatter shield, but will look like this) Alot of you probably never heard of a scatter sheild...
  15. Transmission alley
    Okay I have a quick question about my transmission and clutch that I purchased for it. I have the stock 4 speed transmission in my 90 Civic hatch with the Zc swap and I put a clutchmasters competition stage 4 clutch in the 4 speed transmission. If I buy a 89-91 Si Transmission will the clutch...
  16. Transmission alley
    i found a listing for a clutch for d series but im not sure if all d series have the same clutch pressure plate and throwout bearing. so do they?
  17. Naturally Aspirated
    So yet another question from a new D15b owner. This has been my first swap on the first car I've ever owned. Forgive me if this has been asked 100 times before... I purchased a clutch for my D15b7 since the old one was going at about 235xxx and promptly after the rings in 2 of my cylinders went...
  18. Whoopee Doo Racing
    The MFactory Metal Plate LSD has gone into production and will be ready in 4-6 weeks! These are for 40mm standard axle fitments (non DOHC ZC). Through the smooth and constant distribution of power to the wheels, the MFactory Metal Plate LSD puts the power-to-the-ground and maximises your...
  19. Whoopee Doo Racing
    After speaking with Alex of Action Clutch today I'm ready to throw this out there. Many people are using ebay clutches due to pricing. These clutches use pressure plates that are made in China (not always a bad thing, but not good in this case). Some are also using Exedy organic clutches that...
1-20 of 25 Results
Top