Honda D Series Forum banner

Search results

1-17 of 17 Results
Advanced Search
  1. Vtec malfunction

    General Tech
    Not sure where this should be but I'm getting a code p1259. I have hard wired my solenoid and Rewired my oil pressure switch And it was working fine until this past week. I'm getting the code coming back as soon as I erase them with key on engine off so I'm lead to believe it's a wiring issue...
  2. Knock sensor wiring

    Engine Management
    The second is actually stranded core. Do you recommend any others that are cheaper per ft.?
  3. Idle problem

    Naturally Aspirated
    Makes sense I'll have to give it a whirl after reading on how to do it correctly
  4. Idle problem

    Naturally Aspirated
    So you're saying I need to actually set the idle? I was trying to avoid it until it was the final thing to do as I don't have a tachometer besides what is in the car.
  5. Idle problem

    Naturally Aspirated
    Also checked every vacuum line both visually and with carb cleaner and that showed no vac leaks. Also changed pcv valve (wasn't rattling when changed) and that was no help as well.
  6. Idle problem

    Naturally Aspirated
    Well continuity check on knock sensor is bad and needs rewire. Could this be causing my rough idle and drivability problems?
  7. Idle problem

    Naturally Aspirated
    I'm sure it's been asked a dozen plus times. It's a y8. I'm sorry I've searched and can't locate what to do. I have cleaned my idle air control valve, and throttle body, adjusted my throttle cable at the t.b. and did the proper idle relearn procedure. I have a code for knock sensor I'll be...
  8. Did it jump or is it off a tooth?

    General Tech
    If I'm not able to get it into spec with the dizzy it must be off mechanically and I will need to get a belt kit and just replace it. No sense taking the belt off and not replacing it, the tensioner, and the water pump. Am I right?! Lol
  9. Did it jump or is it off a tooth?

    General Tech
    Ahhh ok. So I need to set the gun at 0° and get the mark lined with the sight. I did just adjust the valve lash last weekend and lined up for tdc and the cam was lined with the mark "up" in the 12 position and the two others level with the head. So I'm guessing tdc is correct as well as...
  10. Did it jump or is it off a tooth?

    General Tech
    Hello everyone. D16Y8 first off. Tried adjusting timing and I'm not very well off in this department. Been chasing down a knock sensor error (replaced it) thought hey what the heck I have a timing light just wanted to make sure it wasn't spark knocking? I mean I have pretty good knowledge when...
  11. Anyone from Central Tenn??

    New Member Introductions
    New here well kinda...just never properly introduced myself... anyone from my area here? And thanks y'all for having me!!
  12. Rear disc swap

    General Tech
    My bad I'm glad to be here and thankful I got the answer I was needing. Next time I will def do some harder research before asking a question sorry again and seriously thanks for the help it's much appreciated. I didn't even think to look at an Acura parts site and cross reference the part numbers.
  13. Rear disc swap

    General Tech
    Well fuck lol.... sorry I'll refrain from asking and thanks for the help
  14. Rear disc swap

    General Tech
    So to keep the answer simple because I'm dumb haha I can use a 4 door Integra arm in a coupe? And thanks for the reply much appreciated!!
  15. Rear disc swap

    General Tech
    97 ex coupe. Will 4 door Integra trailing arms work or are they a different length?
  16. What all needs to be done

    Engine Management
    Well just got me a 97 civic ex d16y8 and there's a few problems with it I'm looking for help with. 1 my temp gauge doesn't work and the pig tail is missing to the sender. What is the wire color for it? 2 my vtec solenoid is unhooked and am trying to locate the other end of the harness wire I'm...
  17. What all needs to be done

    Engine Management
    What's up new member here Well just got me a 97 civic ex d16y8 and there's a few problems with it I'm looking for help with. 1 my temp gauge doesn't work and the pig tail is missing to the sender. What is the wire color for it? 2 my vtec solenoid is unhooked and am trying to locate the other...
1-17 of 17 Results
Top