Honda D Series Forum banner

Search results

1-20 of 28 Results
Advanced Search
  1. O2 sensors on turbo downpipe

    Forced Induction
    K thanks
  2. O2 sensors on turbo downpipe

    Forced Induction
    Current downpipe only has one spot on it for an 02 sensor right after the five bolt flange to the turbo . So since im getting welding done now is the time to add a second spot for 02 sensor if i need it ...?
  3. O2 sensors on turbo downpipe

    Forced Induction
    So my stock y7 manifold has 2 sensors one on top of manifold and a lower one by the cat. Do i need to hook both of those sensors back up after car gets tuned on crome im having more welding done on downpipe so do i need 2 ports ?
  4. Is dyno tune a must for a hondata boosted d

    Forced Induction
    I should refrase that Idont wanna pay a k to a non reputable tuner. Might have to look for one in a bigger city near me..
  5. How do I get rid of CEL # 22 ? (low vtec oil pressure)

    Naturally Aspirated
    Pretty sure its wired right guy who did the swap had done a ton of em and works for honda as a mechanic. Thanks for the help though ! ya oil lev is good tried everything eccept cleaning the screen it came on from day one though so maybee screen was clogged in japan but i doubt it ill try that...
  6. Is dyno tune a must for a hondata boosted d

    Forced Induction
    Ok I wont cheap out. Not paying thick forc tune though f that .. Thanks you guys !! 🙂.....
  7. Is dyno tune a must for a hondata boosted d

    Forced Induction
    So every tuner around here is just stupid expensive. Im boosting my car Its a 96 civic cx with a d15b vtec swap.p28 ecu with the obd1 to 2 jumper harness... garret turbo internal wg with a 5lb spring. Hondata.v3 is on its way in the mail. I can chip it myself piece of cake . Is there anyway to...
  8. What do i need to buy for socket/chip ecu on chrome

    Audio/Electronics
    Hey ! How hard would it be to tune myself ? Dont think I know enough really to do that ..like i think ive hit a brick wall with the crome route and looking like i have to buy hondata . Last straw was wen one of the tuners quoted me same price to tune on crome as on homdata 1000 bucks for ether...
  9. How do I get rid of CEL # 22 ? (low vtec oil pressure)

    Naturally Aspirated
    Hey so the engines a 92-95 d15b 1 vtec solenoid cars a 96 civic cx hatch . Ive had this code since the swap trying to get rid of it. Looks like the guy who swapped it wired and grounded the pressure switch right i hv a p28 ecu with the jumper harness into the obd 2 car . Today i did the vtec...
  10. Is this a good deal d16z6 motor and trans

    General Tech
    I hv a d15b vtec with a y7 trans from the stock motor... around here 200 for an si trans is pretty much the going rate or even on the cheaper side... might just buy it and hopefully sell the z6
  11. Is this a good deal d16z6 motor and trans

    General Tech
    Sorry if this is in the wrong section but someone has a d16z6 motor and trans out of a 93 del sol says thats the same as the si motors and trans its got pretty high km on it though 270000km wondering if it would be a good motor to have as a spare for turbo and or to build or is that too high of...
  12. What do i need to buy for socket/chip ecu on chrome

    Audio/Electronics
    Cool thanks for the info ... I hv a p28 ecu indont wanna buy another one is there a specific chip kit you would recomend and is socketing for a chip kit the same process as desoldering the board to install homdata ?
  13. What do i need to buy for socket/chip ecu on chrome

    Audio/Electronics
    Can anyone recomend what all i need to buy to tune on chrome as far as what i would need to do to my stock ecu?
  14. Oil pan fittment

    Engine Building
    Does a 91 d15 (b7 i think) oil pan fit on a 92-95 gen d15b vtec
  15. Engine Management

    Forced Induction
    Im assuming no to the nitrous and pump gas off the top of my head ... I would hv to check on the rest....
  16. Engine Management

    Forced Induction
    So i wish I had the money for hondata but i dont im going to boost a stock d15b vtec on like 6lbs or something ide be happy with 200hp... My qusetion is would i be able to get an ecu that someone is selling that has been tuned for something else and run with that for example here is one that...
  17. How do I add a block heater to engine

    General Tech
    I hv a d15bvtec it never had a block heater. Does this sound right? How do I add a block heater to my 96 civic with a d15bvtec (92-95 motor) ? 🙂
  18. Downpipe welding question

    General Tech
    I guess its called a butt joint that i was wondering if i hsd to do but best way is lap joint and or sleeve
  19. Downpipe welding question

    General Tech
    Well what i want is the bottom corner of the flange side pipe to go inside the other pipe. But dont know if that way would make a good enough seal for that spot will be getting a little hot right there..
  20. Downpipe welding question

    General Tech
    Had to cut it to clear my ac compressor . Wondering when I weld it back up do the mating surfaces of the pipe need to be completley flush ? Or could i weld it air tight how i have it in pic but just pushed in more ....
1-20 of 28 Results
Top