Honda D Series Forum banner

Search results

1-20 of 178 Results
Advanced Search
  1. Power Steering Tensioner question

    General Tech
    That is the pump I have I have the wing but bolt also What does the wingnut bolt thread into? That is what I think I’m lacking
  2. Power Steering Tensioner question

    General Tech
    I from what I see don’t have a B18c pump but similar it appears Also doesn’t match up to my d16y7 pump either
  3. Power Steering Tensioner question

    General Tech
    It is the P72 bracket Which is installed and pump attached. I have the wingnut bolt just trying to figure out what piece I need to thread it into. Appears like something is missing
  4. Power Steering Tensioner question

    General Tech
    I will try to get a picture of the power steering pump to help explain, but car has a B18c in it. Well this civic at least Bracket is a P72 and is missing the vertical adjuster which allows it to slide back down and squeal
  5. Power Steering Tensioner question

    General Tech
    No just the piece that bolt (9) threads into on diagram. The wingnut bolt. I have everything else
  6. Power Steering Tensioner question

    General Tech
    Ok so I’m trying to tension the power steering pump where it needs to be and realized the car didn’t have part of the items needed to do so. My question is what other piece do I need to complete this so it will stop squealing randomly? Portion missing is piece that the wingnut bolt threads into...
  7. Where to install IAT SENSOR?

    Naturally Aspirated
    When swapping the connectors to do so, I will need to figure out which wires attach to each other. Or will colors of wiring be same on both plugs? Also you are right I just discovered a second plug for an IAT right at manifold running off injectors. As well as current one for intake pipe...
  8. Where to install IAT SENSOR?

    Naturally Aspirated
    Gotcha the grinding idea I didn’t think of. And yes the drilling dry carbon kinda scares me lol I never have good luck so may try that.
  9. Where to install IAT SENSOR?

    Naturally Aspirated
    That’s a thought too lol Been hunting around but can’t even find the plug that should be on the intake manifold sensor
  10. Idle problems

    New Member Introductions
    Similar problem and curious of suggestions Car starts up, idles smooth but high at 1500rpm when warmed up. But will idle at. 950rpm like it should normally with the AC on
  11. Where to install IAT SENSOR?

    Naturally Aspirated
    So the setup is in a 1999 Honda Civic LX 5 speed manual It is swapped to a B18c with skunk2 pro throttle body and manifold and has been chip tuned for setup. Swap done properly with new civic Si motor harness Just general setup of the intake pipe seemed odd not to have any ports to hook up...
  12. Where to install IAT SENSOR?

    Naturally Aspirated
    Well it has one on manifold, it’s the one that actually goes into the intake pipe itself Also can’t seem to find the plug that hooks to the one on the manifold though too
  13. Where to install IAT SENSOR?

    Naturally Aspirated
    Yeah I don’t have any lol Suggestions on how to drill ��������out damaging ?
  14. Where to install IAT SENSOR?

    Naturally Aspirated
    1999 Honda Civic 5 speed manual Purchased a password JDM carbon intake and got it in but see no location for the IAT sensor Where is everyone locating theirs? Or are you drilling a hole in the intake for it? Thanks
  15. Which AC Compressor?

    General Tech
    I do not have the d series motor one unfortunately. I agree thinking the B motor would be choice but wanted to make sure before ordering one up
  16. Which AC Compressor?

    General Tech
    Ok so I have 2 civics, one is in need of an AC compressor. It is a 1999 civic LX but has been swapped before I purchased to a B18C JDM gsr motor Not sure what AC compressor to buy if anyone can help I know it has an AC bracket stamped P72 Not sure if d or b are different at all Getting too hot...
  17. Need Help with Exhaust setup

    New Member Introductions
    Yeah that's what I am finding eye balling it Manifold won't be an issue but exhaust won't direct fit so probably just going to get yonaka cat back and eBay or yonaka header
  18. Need Help with Exhaust setup

    New Member Introductions
    I have a 1997 civic LX 4dr 5 speed manual and exhaust is needing some work. I have a manifold off of a z6 motor and downpipe and a test pipe as well. Will this bolt up to my cat back section directly? Or will it need modified? Figured I would check with the free parts I have first. Searched...
  19. Wtb hx upstream oxygen sensor

    Want to Buy
    Looking for a good working civic hx upstream oxygen sensor. The 5 wire one. Put a header on and broke it lol
  20. In need of assistance with front end problem

    General Tech
    Never noticed the fender differences in that way. Hmm I will have to get somebody to help me this weekend hopefully and try out the methods listed above.
1-20 of 178 Results
Top