Drive axle seals install - D-series.org

Go Back   D-series.org Motor Mayhem & Suspension Satisfaction Transmission alley

D-Series.org is the premier Honda All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 05-15-2010, 04:54 PM   #1 (permalink)
n00b
 
iTrader: (0)
Join Date: Mar 2010
Posts: 16
Rep Power: 0 9t3Si is trying to make new friends
iTrader Score: 0 reviews
Default Drive axle seals install

Hey guys I need your help. My transmission axle seal are leaking and I need to replace it. I have the trans off the car and looking at the seals, I am not sure what's the right way to install the new seals. Do I need a special tool to press in the new seals or any regular tool on hand I can use in combination with technique or manuever to install seal properly. All your suggestions is greatly appreciated. Thanks
9t3Si is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 05-15-2010, 05:37 PM   #2 (permalink)
D-series lover
 
civicskata's Avatar
 
iTrader: (3)
Join Date: Aug 2005
Location: NC
Posts: 207
Rep Power: 15 civicskata is trying to make new friends
iTrader Score: 3 reviews
Send a message via AIM to civicskata
Default

No special tool needed, I just used a small hammer and tapped around the edges till it was in, then use a screwdriver to pry it where it's square and not crooked. Dont push it in too far or you'll have a constant leak. Just even with the outside case it all it takes
civicskata is offline   Reply With Quote Quick reply to this message
Old 05-15-2010, 05:44 PM   #3 (permalink)
Brokedick Millionaire
 
transzex's Avatar
 
iTrader: (59)
Join Date: Dec 2003
Location: Cincity OH
Posts: 40,191
Rep Power: 108 transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !
transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !transzex is on a level you can only DREAM about! ! !
iTrader Score: 59 reviews
Default

I use old transmission bearing races.......

basic tool kit

__________________
Mista Bone



To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


Quote:
Originally Posted by patprimmer RIP
I will always feed an inquisitive mind, prod a lazy noob and blast a disrespectful bum.
transzex is offline   Reply With Quote Quick reply to this message
 
Old 05-16-2010, 07:43 AM   #4 (permalink)
D-series G0D
 
BLK92_D16's Avatar
 
iTrader: (78)
Join Date: Feb 2006
Location: Greenville, SC
Posts: 13,322
Rep Power: 30 BLK92_D16 Still a JDM Star....
BLK92_D16 Still a JDM Star....BLK92_D16 Still a JDM Star....BLK92_D16 Still a JDM Star....BLK92_D16 Still a JDM Star....BLK92_D16 Still a JDM Star....BLK92_D16 Still a JDM Star....BLK92_D16 Still a JDM Star....BLK92_D16 Still a JDM Star....
iTrader Score: 78 reviews
Default

^The above is not needed to replace just the axles seals. Just pop out the old seals using a flat head screwdriver. Lightly oil the outer part of the new seal, and hand-pressin new seal. Place old seal on top of the new and tap into place...not too deep though! The lip of the seal should sit flush with the lip of the case.
BLK92_D16 is offline   Reply With Quote Quick reply to this message
Old 05-16-2010, 11:03 AM   #5 (permalink)
n00b
 
iTrader: (0)
Join Date: Mar 2010
Posts: 16
Rep Power: 0 9t3Si is trying to make new friends
iTrader Score: 0 reviews
Default

Thanks everbody.

Transzex, do have any broken bearing cases? Maybe you can ship it to me I'll just send you the shipping fee? Lmk. Thanks


Quote:
Originally Posted by transzex View Post
I use old transmission bearing races.......

basic tool kit

9t3Si is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the D-series.org forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


iconAll times are GMT -8. The time now is 02:19 AM. | Welcome to Forum, please register to access all of our features.