P0132 - D-series.org

Go Back   D-series.org Ľ Everything Else Ľ New Member Introductions

D-Series.org is the premier Honda All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 02-04-2018, 01:04 AM   #1 (permalink)
n00b
 
iTrader: (0)
Join Date: Aug 2017
Posts: 0
Rep Power: 0 MolonLabe is nobody
iTrader Score: 0 reviews
Default P0132

So I recently did an head swap

98 civic cx

99-00 ex head
99-00 ex intake manifold
D16y17 block
P29 75mm piston
High flow oil pump
98 cx original engine harness
Vtec, knock sensor & IACV wired correctly
ECM - 37820-P2P-A12 M/T (99-00 w/air injection)
1320 RMF header (no cat)
Passwordjdm power chamber intake

During installation of vacuum hose I accidentally broke one of the pipe on the FUEL INJECTION AIR CONTROL VALVE which connects to the intake pipe to the intake manifold. So I temporarily plugged the hose with a 12mm bolt. And so I started the vehicle.

The car runs and seems to idle fine
But after awhile(5mins) DTC sets and I get a P0132 O2 Sensor Circuit High Voltage (Bank 1 Sensor 1)

I have checked if the wires are plugged in correctly and checked for continuity on the harness pins to the ecu connector pins and I do. I canít remember the voltage I was getting while it was idling. Prior to this swap I replaced that sensor and just reused it.

Now Iím thinking could the air control valve that I broke cause this DTC to set or the my actual o2 b1s1 is way too close to the exhaust port as in, I need to move it further down the exhaust manifold? Current location right now is about 12Ē from the exhaust port of the head, unlike the oem which is down below the motor. And if I was to use a o2 defouler, could that help?




Sent from my iPhone using Tapatalk
MolonLabe is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 02-04-2018, 01:10 AM   #2 (permalink)
n00b
 
iTrader: (0)
Join Date: Aug 2017
Posts: 0
Rep Power: 0 MolonLabe is nobody
iTrader Score: 0 reviews
Default D16y8 head swap p0132

So I recently did an head swap

98 civic cx

99-00 ex head
99-00 ex intake manifold
D16y17 block
P29 75mm piston
High flow oil pump
98 cx original engine harness
Vtec, knock sensor & IACV wired correctly
ECM - 37820-P2P-A12 M/T (99-00 w/air injection)
1320 RMF header (no cat)
Passwordjdm power chamber intake

During installation of vacuum hose I accidentally broke one of the pipe on the FUEL INJECTION AIR CONTROL VALVE which connects to the intake pipe to the intake manifold. So I temporarily plugged the hose with a 12mm bolt. And so I started the vehicle.

The car runs and seems to idle fine
But after awhile(5mins) DTC sets and I get a P0132 O2 Sensor Circuit High Voltage (Bank 1 Sensor 1)

I have checked if the wires are plugged in correctly and checked for continuity on the harness pins to the ecu connector pins and I do. I canít remember the voltage I was getting while it was idling. Prior to this swap I replaced that sensor and just reused it.

Now Iím thinking could the air control valve that I broke cause this DTC to set or the my actual o2 b1s1 is way too close to the exhaust port as in, I need to move it further down the exhaust manifold? Current location right now is about 12Ē from the exhaust port of the head, unlike the oem which is down below the motor. And if I was to use a o2 defouler, could that help?








Sent from my iPhone using Tapatalk
MolonLabe is offline   Reply With Quote Quick reply to this message
Old 02-04-2018, 06:30 AM   #3 (permalink)
BATSLOMAN GIVES 0 FUCKS
 
slo_eg8's Avatar
 
iTrader: (28)
Join Date: Mar 2009
Location: TAMPA FLORIDA
Posts: 3,854
Rep Power: 50 slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !
slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !
iTrader Score: 28 reviews
Send a message via AIM to slo_eg8
Default

thank you for making 2 exact threads 6 minutes apart.
__________________
turbo d16z6
.42/.48 garrett
je pistons, eagle rods, y7 lsd trans w/4.3fd
koni yellow/gc coils
uber rare eg6 optional snowflakes

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

new 95 ej1.
slo_eg8 is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the D-series.org forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Security Question
*Required, this field is not shown to others: While balancing on a piece of wood, two inches by four inches known as a 2x4, john and his friend sally both spotted a dalmatian inside a truck with sirens, headed to put out a fire. State what kind of animal is mentioned in the sentence above.
Insurance
Please select your insurance company (Optional)

Log-in



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


iconAll times are GMT -8. The time now is 08:26 AM. | Welcome to Forum, please register to access all of our features.