boost d16z6 head with d15z1 bottom end combo. ptw clearance?? - D-series.org

Go Back   D-series.org Everything Else New Member Introductions

D-Series.org is the premier Honda All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 08-29-2016, 09:07 AM   #1 (permalink)
n00b
 
1CAM-HAMMA's Avatar
 
iTrader: (0)
Join Date: Aug 2016
Posts: 32
Rep Power: 0 1CAM-HAMMA is a DOUCHE BAG
iTrader Score: 0 reviews
Post boost d16z6 head with d15z1 bottom end combo. ptw clearance??

I'm building an oem vitara build aka as the but with oem parts d16z6 head with a d15z1 bottom end for boost.
many guys said that this will end up like a 7. to 1 low compression or a 8 to one compression setup. i will run this setup for turbo. possible high boost with a good tune.

i have a d16z6 head that is oem spec new fresh seals etc build. arp head studs and bolts. oem head gasket

i will use the d15z1 bottom end
full crank assembly with oem coded bearings. the crank got mic and was all standard shop said it was okay.
the engine was a high milage everything is ok but the bore is close within the service limits the shop told me a hair over.




i haven't measure the piston to find the piston to wall clearance but is this acceptable? if the bore is service limits maybe hair over? the shop said that the pistons where ok but bore is service limit.

heat boost is that ok with using the oem pistons. how much ptw cleanse i can use with this.

i want to oem low comp build what would be this be acceptable for ptw cleanace?
__________________
Project D16z6 Head with D15z1 Block.

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
SINGLE CAMMER HAMMER
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
1CAM-HAMMA is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 08-29-2016, 02:19 PM   #2 (permalink)
BATSLOMAN GIVES 0 FUCKS
 
slo_eg8's Avatar
 
iTrader: (28)
Join Date: Mar 2009
Location: TAMPA FLORIDA
Posts: 3,871
Rep Power: 50 slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !
slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !
iTrader Score: 28 reviews
Send a message via AIM to slo_eg8
Default

you have to measure p2w after you get the pistons youre going to use. have you bored the cylinders?
__________________
turbo d16z6
.42/.48 garrett
je pistons, eagle rods, y7 lsd trans w/4.3fd
koni yellow/gc coils
uber rare eg6 optional snowflakes

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

new 95 ej1.
slo_eg8 is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the D-series.org forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


iconAll times are GMT -8. The time now is 03:04 AM. | Welcome to Forum, please register to access all of our features.