cam belt tensioner - D-series.org

Go Back   D-series.org Motor Mayhem & Suspension Satisfaction DOHC ZC

D-Series.org is the premier Honda All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 03-01-2016, 10:12 PM   #1 (permalink)
n00b
 
iTrader: (0)
Join Date: Oct 2011
Posts: 12
Rep Power: 0 bkevbush is nobody
iTrader Score: 0 reviews
Default cam belt tensioner

recently changed cam belt on my d16a9 twin cam.tensioned up to what seems right but after a few hundred miles it seems to slacken a bit on right hand run looking end on.runs fine not jumping so i tightened it up again and again after so many miles its slackened off again.i dont want to over tighten tensioner bolt and strip thread.do they kind of find theyre tension ive had no trouble other wise
bkevbush is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 03-02-2016, 05:50 AM   #2 (permalink)
BATSLOMAN GIVES 0 FUCKS
 
slo_eg8's Avatar
 
iTrader: (28)
Join Date: Mar 2009
Location: TAMPA FLORIDA
Posts: 3,853
Rep Power: 50 slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !
slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !slo_eg8 is on a level you can only DREAM about! ! !
iTrader Score: 28 reviews
Send a message via AIM to slo_eg8
Default

did you do it per oem instructions?
__________________
turbo d16z6
.42/.48 garrett
je pistons, eagle rods, y7 lsd trans w/4.3fd
koni yellow/gc coils
uber rare eg6 optional snowflakes

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

new 95 ej1.
slo_eg8 is offline   Reply With Quote Quick reply to this message
Old 03-14-2016, 11:06 PM   #3 (permalink)
n00b
 
iTrader: (0)
Join Date: Oct 2011
Posts: 12
Rep Power: 0 bkevbush is nobody
iTrader Score: 0 reviews
Default

i have workshop manual cam lock kit etc,was replacing after a failure so had to re time but otherwise yes.engine is still running fine after prob around 1000 miles.ive left the cover off so i can keep an eye on it,i ll have to re tension when i replace cover anyway as belt has to be removed to put rear cover on
bkevbush is offline   Reply With Quote Quick reply to this message
 
Old 03-15-2016, 04:34 AM   #4 (permalink)
D-series G0D
 
mattliston's Avatar
 
iTrader: (10)
Join Date: Apr 2009
Location: La Crosse,WI
Posts: 5,771
Rep Power: 32 mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !
mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !mattliston is on a level you can only DREAM about! ! !
iTrader Score: 10 reviews
Default

did you replace the spring for the tensioner while you were in there?

by this time its probably a hard part to come by.

but should be replaced at the same time as the timing belt and tensioner
__________________

2003 Hyundai Sonata GLS 2.7 Delta 197k
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

1998 Cadillac Seville SLS just broke 100k
2001 civic LX coupe MTX 199k
Sometimes, the difficult path is the easiest path
D/B/F/H/K compression questions?

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.



To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Build what you have!
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

mattliston is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the D-series.org forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:
Security Question
*Required, this field is not shown to others: While balancing on a piece of wood, two inches by four inches known as a 2x4, john and his friend sally both spotted a dalmatian inside a truck with sirens, headed to put out a fire. State what kind of animal is mentioned in the sentence above.
Insurance
Please select your insurance company (Optional)

Log-in



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


iconAll times are GMT -8. The time now is 07:13 PM. | Welcome to Forum, please register to access all of our features.