Edm Zc1 - D-series.org

Go Back   D-series.org Motor Mayhem & Suspension Satisfaction DOHC ZC

D-Series.org is the premier Honda All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 09-29-2005, 10:59 AM   #1 (permalink)
NuKi
Guest
 
Posts: n/a
Default Edm Zc1

Hi guys.

New here, so I have a couple of questions.

I have a 1986 CRX with a browntop EDM ZC. Its rated at 125 hp.
Does everything that fit ZC in general fit this engine as well?
Are there any OEM-pistons I can use that yields higher CR?
What about clutches? I know it has 21splines and measures 200mm, but witch one exactly can I purchase?
Are there any headers that can be used w/o portmatching? That is made for ZC?
The ignition is vacuum-advanced, so practically I cant tune it?
How do I tune it if I add larger cams and so on?
Which cams can be used with stock springs?
Ive once read that Bseries or H22-throttlebodies fit any D-series intakemanifold. Is this possible on the ZC also?
Everyone here in Sweden says that B16 is the only thing, but I want to try something else. Have had a few VTECs before, so can I make good performance out of this?

Sorry for the load of qs

Regards

Niklas, Sweden
  Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 10-04-2005, 10:11 AM   #2 (permalink)
NuKi
Guest
 
Posts: n/a
Default ...

Any suggestions?

NuKi
  Reply With Quote Quick reply to this message
Old 10-04-2005, 10:31 AM   #3 (permalink)
D-series PIMP
 
EJ1All-Star's Avatar
 
iTrader: (8)
Join Date: Jul 2005
Location: Utah
Posts: 1,034
Rep Power: 15 EJ1All-Star is da #1 stunnaEJ1All-Star is da #1 stunnaEJ1All-Star is da #1 stunnaEJ1All-Star is da #1 stunnaEJ1All-Star is da #1 stunnaEJ1All-Star is da #1 stunnaEJ1All-Star is da #1 stunna
iTrader Score: 8 reviews
Send a message via AIM to EJ1All-Star Send a message via MSN to EJ1All-Star
Default

my only expierence is with black top zc's I don't know very much on the edm browns, try another website thats more dedicated to zc's u might find some gearheads in thier with some great info, Thezcr.com great site good people, not saying this site is bad but no help in a couple of days i'd try a new website too.
EJ1All-Star is offline   Reply With Quote Quick reply to this message
 
Old 10-05-2005, 12:30 AM   #4 (permalink)
NuKi
Guest
 
Posts: n/a
Default

Hehe, roger that
  Reply With Quote Quick reply to this message
Old 10-05-2005, 07:55 AM   #5 (permalink)
 
iTrader: (0)
Join Date: Jan 2005
Posts: 432
Rep Power: 0 Black Mountain will become famous soon enoughBlack Mountain will become famous soon enoughBlack Mountain will become famous soon enough
iTrader Score: 0 reviews
Default

Ok........

Browntop and blacktop ZC's are mechanically the same.........


the only real difference is the Dizzy, #1 cylinder position sensor and intake manifold (including sensors on that)

if your in the USA....

go to the junkyard and get 88-89 integra pistons...these are domed and pop right in...(same block)

also fyi all bearings seals rods ect are the same as the 86-89 integra...

the whole browntop thing is pretty much intirlly based on wiring...
The 86-87 integra came with the exact same engne as what you have................


Ok I just noticed that you are in sweden......


Blacktop Civic/Crx ZC or d16a9 (not sohc or b16) pistons they are the same bore everything.....they will pop right in....you can even use the piston rings listed for your car


also


www.RedpepperRacing.com

that site is the absolute shit for what you need to know....those guys speciallize in your exact car!

Last edited by Black Mountain; 10-06-2005 at 08:08 AM.
Black Mountain is offline   Reply With Quote Quick reply to this message
Old 10-06-2005, 11:20 AM   #6 (permalink)
NuKi
Guest
 
Posts: n/a
Default

Yeah, I know bout redpepper. Just thought I should check other sources too.
Thanks for your answer, perhaps aftermarket piston would do. Our engines are kinda low compression, so a slight bump there should result in some hp. Or does the blacktop or d16a9 give the same result? Are there any cheap cams I can use with standard valvetrain?

Nuki
  Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the D-series.org forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


iconAll times are GMT -8. The time now is 06:40 PM. | Welcome to Forum, please register to access all of our features.