GO-AUTOWORKS Injector Dynamics Install Walk Through (ID1000) - D-series.org

Go Back   D-series.org D-series Knowledge Factory DIY Forum

D-Series.org is the premier Honda All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 01-28-2011, 02:36 PM   #1 (permalink)
D-series G0D
 
iTrader: (164)
Join Date: Jul 2006
Location: GO-AUTOWORKS.COM
Posts: 6,837
Rep Power: 23 GO-AUTOWORKS is the fucking MAN!!!!GO-AUTOWORKS is the fucking MAN!!!!GO-AUTOWORKS is the fucking MAN!!!!
GO-AUTOWORKS is the fucking MAN!!!!GO-AUTOWORKS is the fucking MAN!!!!GO-AUTOWORKS is the fucking MAN!!!!GO-AUTOWORKS is the fucking MAN!!!!
iTrader Score: 164 reviews
Default GO-AUTOWORKS Injector Dynamics Install Walk Through (ID1000)

Here's a quick walk through install on the Injector Dynamics ID1000.

We offer them here...
https://www.d-series.org/forums/go-au...ml#post2227064

The Injector set with clips:




These are by far the simplest aftermarket injectors to install !

This write up will contain photos from a K Series install, which install basically the same on the D series.

Start by releiving some of the fuel pressure by opening the gas tank lid. Then at the bay, start by removing the factory wiring from the fuel rail and detach the OE clips from the injectors. Loosen the rail and pull it off. The stock injectors will typically come out with it. (On the D/B series, a small pic is a great tool to use to open the retainer pin on the OE clips)


Here is a comparison next to the stock RSX-S injector


Next, go ahead and unloom the stock harness so you have ample room to cut and reconnect the new injector clips supplied. For this a soldering iron, heat shrink, and electrical tape is required)

Clip the stock injectors off and install the new clips. It is advised to solder and heat shrink the connection. Remember to slide the heat shrink on before you connect the wire and have it far away enough from the iron so that it doesnt shrink wile soldering.



Once all 4 are done, simply install the injector in the rail, install the rail back to the manifold with the injectors in the appropriate position, and reconnect them. (The RSX OEM rail clips fit the ID1000s just as they fit the stock injectors)

You can use the stock harness covering again for an OE look


Finished
GO-AUTOWORKS is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 01-29-2011, 05:42 AM   #2 (permalink)
D-series soldier
 
D2ZBOY's Avatar
 
iTrader: (5)
Join Date: May 2009
Location: Beaufort, SC
Posts: 983
Rep Power: 11 D2ZBOY is da #1 stunnaD2ZBOY is da #1 stunnaD2ZBOY is da #1 stunnaD2ZBOY is da #1 stunnaD2ZBOY is da #1 stunnaD2ZBOY is da #1 stunnaD2ZBOY is da #1 stunna
iTrader Score: 5 reviews
Default

Nice write up.
D2ZBOY is offline   Reply With Quote Quick reply to this message
Old 01-29-2011, 05:45 AM   #3 (permalink)
Will Do Handstands For Pussy!!!
 
JDMek's Avatar
 
iTrader: (17)
Join Date: May 2008
Location: Tuscaloosa, AL
Posts: 2,875
Rep Power: 22 JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!
JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!JDMek is the fucking MAN!!!!
iTrader Score: 17 reviews
Send a message via AIM to JDMek
Default

Those are like the BEST injectors lol
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
JDMek is offline   Reply With Quote Quick reply to this message
 
Old 02-02-2011, 02:09 PM   #4 (permalink)
D-series soldier
 
xkrazyxjbrkerx75's Avatar
 
iTrader: (9)
Join Date: Feb 2009
Location: Illinois
Posts: 645
Rep Power: 11 xkrazyxjbrkerx75 is learning the way of the Dxkrazyxjbrkerx75 is learning the way of the D
iTrader Score: 9 reviews
Default

is their a special wiring color order you need to install the injector clips? or can you just solder all the clips to any injector order.
__________________
Built z6~ Th1rsty 4 Th4t B00ST
xkrazyxjbrkerx75 is offline   Reply With Quote Quick reply to this message
Old 02-03-2011, 03:06 AM   #5 (permalink)
D-series G0D
 
iTrader: (164)
Join Date: Jul 2006
Location: GO-AUTOWORKS.COM
Posts: 6,837
Rep Power: 23 GO-AUTOWORKS is the fucking MAN!!!!GO-AUTOWORKS is the fucking MAN!!!!GO-AUTOWORKS is the fucking MAN!!!!
GO-AUTOWORKS is the fucking MAN!!!!GO-AUTOWORKS is the fucking MAN!!!!GO-AUTOWORKS is the fucking MAN!!!!GO-AUTOWORKS is the fucking MAN!!!!
iTrader Score: 164 reviews
Default

The order of the clips does not matter since the 4 clips are the same. I always solder the 2 wires with the new clip in the same orientation as the old clip.
GO-AUTOWORKS is offline   Reply With Quote Quick reply to this message
Old 02-17-2011, 11:29 AM   #6 (permalink)
wise in the ways of the D
 
xxjdmcivicek9xx's Avatar
 
iTrader: (29)
Join Date: Jul 2009
Location: Colorado
Posts: 1,797
Rep Power: 16 xxjdmcivicek9xx is hot as a volcanoxxjdmcivicek9xx is hot as a volcano
xxjdmcivicek9xx is hot as a volcanoxxjdmcivicek9xx is hot as a volcanoxxjdmcivicek9xx is hot as a volcano
iTrader Score: 29 reviews
Default

maybe mention that the ID Injectors for the d series require you to install the extra top hat so that it goes into our fuel rail...i used petroleum jelly to lube the O ring for the top hat and when installing it into the actual fuel rail.
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.

2010-294whp D16Y7 T3/T4 24psi E85 12.77 @ 111mph!

2011-360whp D16Y7 GT3076R 25psi E85 12.05 @ 115mph!

2012-414whp D16Y7 GT3076R 28psi E85 11.68 @ 124mph!

Current Ride- 09 Acura TSX
xxjdmcivicek9xx is offline   Reply With Quote Quick reply to this message
Old 04-08-2011, 08:33 AM   #7 (permalink)
D-series soldier
 
xkrazyxjbrkerx75's Avatar
 
iTrader: (9)
Join Date: Feb 2009
Location: Illinois
Posts: 645
Rep Power: 11 xkrazyxjbrkerx75 is learning the way of the Dxkrazyxjbrkerx75 is learning the way of the D
iTrader Score: 9 reviews
Default

Quote:
Originally Posted by xxjdmcivicek9xx View Post
maybe mention that the ID Injectors for the d series require you to install the extra top hat so that it goes into our fuel rail...i used petroleum jelly to lube the O ring for the top hat and when installing it into the actual fuel rail.
This...

i fitted them on my d16z6 skunk 2 pro series intake manifold and their was a little bit of slack and didnt seem like they fit right.. Do you guys sell the o-rings that go into the intake manifold?
__________________
Built z6~ Th1rsty 4 Th4t B00ST
xkrazyxjbrkerx75 is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the D-series.org forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


iconAll times are GMT -8. The time now is 10:59 PM. | Welcome to Forum, please register to access all of our features.