Z6 Block Clearances Spec. Chart - D-series.org

Go Back   D-series.org » D-series Knowledge Factory » Archived Technical Info Posts

D-Series.org is the premier Honda All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 05-07-2005, 08:29 PM   #1 (permalink)
sammydhoff
Guest
 
Posts: n/a
Thumbs up Z6 Block Clearances Spec. Chart

Below is a list I compiled of all the clearance specifications for the D16Z6 Block, it is taken from the 1995 Civic Helm's Factory Service Manual, I decided to make a nice chart for quick reference when doing my engine build, and so I dont fill the pages of my nice new service manual with grease and dirt like I did my Chilton's. I had to split it up into two posts because it exceedes 10,000 characters.

If anyone would like a copy of the actual MS word (.doc) file send me an email and I will send it to you, I tried to attach it to this post but the file size was too large. The actual file looks better. If you need any other info from the book email me. If you wanna buy your own go to www.helmsinc.com , thats the website that the service tech at my local Honda dealership directed me to. The book is the best I have ever seen, walks all over a Chiltons.
Enjoy!!!!!!!


Honda D16Z6 Engine Block Clearance Specifications



Connecting Rod End Play:

Standard (New): 0.15-0.30mm (0.006-0.012in)

Service Limit 0.40mm (0.016in)



Crankshaft End Play:

Standard (New): 0.10-0.35mm (0.004-0.014in)

Service Limit 0.45mm (0.018in)



Main Bearing-to-Journal Oil Clearance:

Standard (New): No. 1,5 Journals: 0.018-0.036mm (0.0007-0.0014in)

No. 2,3,4 Journals: 0.024-0.042mm (0.0009-0.0017in)

Service Limit 0.05mm (0.002in)



Connecting Rod Bearing-to-Journal Oil Clearance:

Standard (New): 0.020-0.038mm (0.0008-0.0015in)

Service Limit 0.05mm (0.002in)



Crankshaft Total Indicated Runout:

Standard (New): 0.03mm (0.001in) max.

Service Limit 0.04mm (0.002in)



Journal Out-of–Round:

Standard (New): 0.0025mm (0.00010in) max.

Service Limit 0.005mm (0.0002in)



Journal Taper:

Standard (New): 0.0025mm (0.00010in) max.

Service Limit 0.005mm (0.0002in)



Piston Diameter:

Standard (New): 74.980-74.990mm (2.9520-2.9524in)

Service Limit 74.970mm (2.9516in)



Piston-to-Block Clearance:

Standard (New): 0.010-0.040mm (0.0004-0.0016in)

Service Limit 0.05mm (0.002in)



Oversize Piston Diameter:

0.25: 75.230-75.240mm (2.9618-2.9622in)

0.50: 75.480-75.490mm (2.9716-2.9720in)









Cylinder Bore Size:

Standard (New) X: 75.000-75.020mm (2.9528-2.9535in)

Standard (New) Y: 75.000-75.015mm (2.9528-2.9533in)

Service Limit 75.070mm (2.9555in)

Oversize

0.25: 75.250-75.270mm (2.9626-2.9634in)

0.50: 75.500-75.520mm (2.9724-2.9732in)



Bore Taper

Limit: Difference between 1st and 3rd

measurement:

0.05mm (0.002in)



Reboring Limit:

Limit: 0.50mm (0.020in)



Normal Bore Size:

D16Z6 Engine: 48.0mm (1.89in)

Except D16Z6 Engine: 45.0mm (1.77in)
  Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 05-07-2005, 08:30 PM   #2 (permalink)
sammydhoff
Guest
 
Posts: n/a
Thumbs up

Piston Pin Diameter:

Standard (New): 18.994-19.000mm (0.7478-0.7480in)

Oversize: 18.997-19.003mm (0.7479-0.7481in)



Piston Pin-to-Piston Clearance:

Standard (New): 0.010-0.022mm (0.0004-0.0009in)



Piston Pin-to-Connecting Rod Inteference:

Standard (New): 0.014-0.040mm (0.0006-0.0016in)



Piston Ring End Gap:



Top Ring

Standard (New): 0.15-0.30mm (0.006-0.012in)

Service Limit 0.60mm (0.024in)



Second Ring

Standard (New): 0.30-0.45mm (0.012-0.018in)

Service Limit 0.70mm (0.028in)



Oil Ring

Standard (New):

D16Z6 Engine: 0.20-0.70mm (0.008-0.028in)

D15Z1 Engine: 0.20-0.50mm (0.008-0.020in) *1

0.20-0.70mm (0.008-0.028in) *2

Service Limit 0.80mm (0.031in)

*1: Teikoku Piston Ring Manufacture

*2: Riken Piston Ring Manufacture



D15B7, D15B8 Engines: 0.20-0.80mm (0.008-0.031in)

Service Limit 0.90mm (0.035in)



Ring-to-Groove Clearance:



Top Ring Clearance

Standard (New)

D15Z1 Engine: 0.035-0.060mm (0.0014-0.0024in)

Except D15Z1 Engine: 0.030-0.060mm (0.0012-0.0024in)

Service Limit 0.13mm (0.005in)



Second Ring Clearance

Standard (New)

D15Z1 Engine: 0.035-0.060mm (0.0014-0.0024in)

*1

0.030-0.055mm (0.0012-0.0022in)

*2

Except D15Z1 Engine: 0.030-0.055mm (0.0012-0.0022in)

Service Limit 0.13mm (0.005in)



*1: Teikoku Piston Ring Manufacture

*2: Riken Piston Ring Manufacture



Piston Ring Grooves:

Top Ring Groove: 1.0mm (0.04in) wide (D15Z1)

or 1.2mm (0.05in) wide

(except D15Z1)

Second Ring Groove: 1.2mm (0.05in) wide (D15Z1)

or 1.5mm (0.06in) wide

(except D15Z1)

Oil Ring Groove: 2.8mm (0.11in) wide
  Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the D-series.org forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


iconAll times are GMT -8. The time now is 04:48 PM. | Welcome to Forum, please register to access all of our features.