Some more D17 info - D-series.org

Go Back   D-series.org Motor Mayhem & Suspension Satisfaction 7th Gen

D-Series.org is the premier Honda All Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
Old 12-28-2004, 10:24 PM   #1 (permalink)
CRX KING
 
slebidia's Avatar
 
iTrader: (12)
Join Date: Dec 2003
Location: Oklahoma
Posts: 1,732
Rep Power: 20 slebidia is hot as a volcano
slebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcanoslebidia is hot as a volcano
iTrader Score: 12 reviews
Send a message via AIM to slebidia
Default Some more D17 info

Using a D17A1 crank, pistons, and rods in a A6 block will yeild a .045 piston to deck height. This should be the same for the D17 blocks since I compared measurements from the D17A1 block and D16A6 block by measureing the crank journal to the deck height on both. Using the D-series compression calculator and using the piston to deck height of .045, Y8 head gasket thicknedd and 32.8 cc's for the combustion chamber I come up with a -7.05 dish for the pistons to get a 9.5:1 compression ratio like the D17A1 is supposed to have. One more thing. If you use the D17 crank and rods in a D16 block or an A6 block at least then nothing is required for the rods to clear. Now to work on the crank pulley issue....
__________________

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
slebidia is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Old 12-30-2004, 10:43 PM   #2 (permalink)
 
iTrader: (0)
Join Date: Oct 2004
Posts: 287
Rep Power: 0 skittyscott is da #1 stunnaskittyscott is da #1 stunnaskittyscott is da #1 stunnaskittyscott is da #1 stunnaskittyscott is da #1 stunnaskittyscott is da #1 stunnaskittyscott is da #1 stunna
iTrader Score: 0 reviews
Default

sounds like you have a lot of time on your hands..
are you trying to build an a6 motor with what you've got lying around??
skittyscott is offline   Reply With Quote Quick reply to this message
Old 02-22-2007, 01:17 PM   #3 (permalink)
D-Series cadet
 
Pvon's Avatar
 
iTrader: (0)
Join Date: Feb 2007
Location: Philly
Posts: 314
Rep Power: 13 Pvon  is slowly gaining respectPvon  is slowly gaining respectPvon  is slowly gaining respectPvon  is slowly gaining respectPvon  is slowly gaining respect
iTrader Score: 0 reviews
Send a message via AIM to Pvon
Default

Yea this thread is old as hell but I couldnt find anything else close to what I was looking for. Eventually Im planning on using a d17 crank in a d16a6. Id use the d17 pan and oil pump and machine the crank for the d16 crank pulley. What I wanted to know is (and this will help you d17ers too) would it be possible to machine the bottom end of forged d16 rods down to fit the d17 crank?

The setup I was thinking of was vitaras and d17 crank and eagle d16 rods. With the a6 head this setup would yeild about 9.5:1 comp according the the calculator.

Last edited by Pvon; 02-22-2007 at 04:54 PM.
Pvon is offline   Reply With Quote Quick reply to this message
 
Old 02-25-2007, 08:50 PM   #4 (permalink)
 
iTrader: (0)
Join Date: Jun 2006
Posts: 188
Rep Power: 0 KingOfQb won't last long at this rate
iTrader Score: 0 reviews
Default

i have been trying to figure this out for the last month anyone know?
KingOfQb is offline   Reply With Quote Quick reply to this message
Old 04-25-2007, 02:28 PM   #5 (permalink)
 
iTrader: (0)
Join Date: Apr 2007
Posts: 59
Rep Power: 0 crimson-crx is nobody
iTrader Score: 0 reviews
Default

great post man some useful info
crimson-crx is offline   Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the D-series.org forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in



Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On


iconAll times are GMT -8. The time now is 11:15 PM. | Welcome to Forum, please register to access all of our features.