intake???

[breu24]

i have a 90 civic hb with a d16z6 and i cant come up with a good, solid intake setup, anyone have any suggestions or methods on what to do? thanks

[93HONDABOY]

JUST GET A PIECE O CRAP INATKE FROM APC. RUNN THAT FOR A LIL SEE HOW MUCH BETTER YOU D16Z6 RUNS DEN SAVE UP AND GET A BETTER ONE. AEM,SKUNK2. OR SOMETHING

[custom_junky]

i would suggest a v2, and a slighty bigger throttle body, and DEFINITELY a better intake mani. be careful about the size of the throttle body you can only go so big before they start to cause air flow problems, anyone got any info about throttle body sizes?

[dxmannn]

get a ebay iem one and go buy a K&n filter and call it a day... all intakes are the same (excpect iceman) they use a pice of metal and a Filter. Aem and Ingen the top intake providers(iceman the best) use the same metal pice and they use a k&n filter dont waste money on name brand intakes get a knock off and a K&n filter and call it a day

[breu24]

yea i understand but they dont make an intake that will fit that motor in my car, do i buy the del sol intake? or a civic intake?

[ottomaticjack]

Just get a short ram off ebay, then get some conduit from home depot and a rubber or silicone coupler, and run the filter out where the resonator box was (assuming you have taken it out or will take it out.)

[kyosoeg6]

get a ebay iem one and go buy a K&n filter and call it a day... all intakes are the same (excpect iceman) they use a pice of metal and a Filter. Aem and Ingen the top intake providers(iceman the best) use the same metal pice and they use a k&n filter dont waste money on name brand intakes get a knock off and a K&n filter and call it a day

i never though somebody would have the same beliefes as me. i think iceman is by far the best intake anybody could possibly buy for the money new or used.

[DJ_SaNdOz]

I removed my resonater, and stock airbox piping & then attached an ebay SRI to teh stock airbox, and I am very satisfied. I am contemplating getting some dryer ducting to make a CAI out of it. It's a cost effective way to make an ice box. overall, an intake is an intake - get what makes you happy.

[f00ker]

take the resonator out if you like extra noise....I'm never removing mine again....

[n_23_s]

port match the intake manifold with the head, get a tb spacer, get a 63mm or bigger tb, get a injen cai or race intake they kick ass. my injen intake is 3 1/2" most aem and other intakes are 2" which suck

[dxmannn]

get a ebay iem one and go buy a K&n filter and call it a day... all intakes are the same (excpect iceman) they use a pice of metal and a Filter. Aem and Ingen the top intake providers(iceman the best) use the same metal pice and they use a k&n filter dont waste money on name brand intakes get a knock off and a K&n filter and call it a day

i never though somebody would have the same beliefes as me. i think iceman is by far the best intake anybody could possibly buy for the money new or used.

yes i love my damn iceman intake ..
back to the subject go buy a short ram one and cut it so it rits or go to home depot and buy some steel pipes and get some rubber flex pipes (plumming section) and make ya own

[JLAUDIOinCIVIC]

didnt read all this shit... but i had a autozone short ram..did good.. traded it for a AEM CAI YYA!

[breu24]

who makes a decent throttle body? anyone have any suggestions?

[kyosoeg6]

who makes a decent throttle body? anyone have any suggestions?

just get a 94+ bseries tb 60mm or the itr tb 62mm

[Honda4VW]

get a tb spacer, get a 63mm or bigger tb

Don't waste your time with either of these

[breu24]

why not?

[exospeed*com]

dont overspend on Intake systems. How much better can a AEM V2 be compared to a reg basic pipe and filter. Come on. 2-3HP. is it really that worth it for 5 times the price?

Spend on the stuff that will really make a difference. I hit 13.6 on my D16a6 with a GSR rubber intake with a K&N cone at the end.