The Offical: Post Your .bin thread...

[JaredKaragen]

Pretty simple: A thread for everyone to shof off their .bin's and setups running them, that way if someone wants a .bin they can search this thread for a setup that someone has that is close to theirs, and they can get a .bin to suit!

WARNING: These .BIN's might not be intended for your setup. they can be configured for larger injectors or a whole slurry of other things.... so be carefull not to blow your motor by running an incorrect .BIN!!!

So here's mine:

Currently:
D15B, P08[w/o2 heater added], 5Spd ZC Transmission, stock fuel system, 2 1/4" exhaust [all high-flow] no resonator), pacesetter 4-2-1 headers, custom _very_ shortram intake, TB Spacer.

TUNED WITH: CROME

ROM OPTIONS:
REDLINE=7500Rpm
Target Idle=800Rpm
VTEC=5188Rpm
IAB=N/A
Speed Limiter=N/A

[x]Disable Knock Sensor
[ ]Disable ELD
[x]Disable AP Sensor
[x]Disable Injector Test Circuit
[ ]Disable o2 Sensor(open loop)
[ ]Disable o2 Heater
[ ]Disable VTEC Speed Check
[x]Disable VTEC Coolant Temp Check
[x]Disable VTEC Pressure Check
[ ]Disable VTEC Solenoid Check

[ ]Debug Mode

PLUGINS INSTALLED IN ROM:
Quick Datalog/RTP
Remove Checksum Routine

http://www.d-series.org/forums/attachment.php?attachmentid=12996&d=1161999604

[ryan89crx]

you should post what program it was done in as well

[gimmezell]

See sig for setup.

Tuned with Crome.

ROM OPTIONS:
REDLINE=7411Rpm
Target Idle=950Rpm
VTEC=5500Rpm
IAB=5750Rpm
Speed Limiter=N/A

[x]Disable Knock Sensor
[x]Disable ELD
[x]Disable AP Sensor
[x]Disable Injector Test Circuit
[ ]Disable o2 Sensor(open loop)
[ ]Disable o2 Heater
[ ]Disable VTEC Speed Check
[ ]Disable VTEC Coolant Temp Check
[ ]Disable VTEC Pressure Check
[ ]Disable VTEC Solenoid Check

Dyno Sheet

http://ej8squad.com/showthread.php?tid=14&pid=52#pid52

[JaredKaragen]

Post updated :TU:

[Rease3]

any turbo setups?

[gimmezell]

Too bad this thread didn't "take off".

[spool'nsol]

people are just too lazy to post all that probably

[Honda4VW]

Threads like this can be scary. Every car is custom, every bin posted is custom to their respective car. Its only a matter of time until someone that is not empowered with knowledge, grabs one of your bins, runs their car and breaks something.

Be careful with your tunes.

[JaredKaragen]

but it's up to someone to have 1/2 a brain cell to see a setup _similar_ to yours, and try it... or even compare it to stock to research etc....

[gimmezell]

but it's up to someone to have 1/2 a brain cell to see a setup _similar_ to yours, and try it... or even compare it to stock to research etc....

I agrree.

[jimmyb34]

but it's up to someone to have 1/2 a brain cell to see a setup _similar_ to yours, and try it... or even compare it to stock to research etc....



lol youve seen some of the people on the net..... lol come on now, you cant give everyone the benefit of the doubt...

[konigcivic]

here is mine

y7 non-vtec
t3 60trim
3" downpipe and exhaust
dsm 450
12* base timing
so far up to 9 psi with no signs of detonation
if you stay out of boost you should get 30mpg
low 11's afr's in boost and they dip into the high 10's in fifth gear.
redline 7100
ftl 3500
boost cut 11.2psi
idle 750 rpm
po6 ecu
crome 1.22

this is just a base map i made, works fine in my car. i have a wideband and something to detect knock. SO SHOULD YOU! with that being said use at your own risk.

[Got Vtec?]

A disclaimer of some kind would not be bad idea either. At least for the dumb people:hammer:

[K2e2vin]

This is the old basemap I made for my ITBs...I no longer have the manifold but working on a new setup. Don't know if this is the same that I had on the Ostrich, but it's the only one I can find that I have left.

D15B VTEC
crappy ITB Manifold(hacked DPFI)/gsxr1000 50-42mm ITB, 2"x6" vac manifold.
Ebay 4-2-1 header with 2" manifold

Crome 1.2, ITB Tools Plus 0.5, GSXR TPS, P30 map but P28 ECU

[x]Disable Knock Sensor
[ ]Disable ELD
[x]Disable AP Sensor
[x]Disable Injector Test Circuit
[ ]Disable o2 Sensor(open loop)
[ ]Disable o2 Heater
[ ]Disable VTEC Speed Check
[ ]Disable VTEC Coolant Temp Check
[ ]Disable VTEC Pressure Check
[ ]Disable VTEC Solenoid Check